DE | EN
configure product
DE | EN
  1. Products
  2. Dispensing Systems
  3. QC Dispense and Fill Heads
  4. Options Dispense and Fill Heads
  5. QC2 Dispense Head Incorporated with Turbine Flow Meter

Options Dispense and Fill Heads

QC2 Dispense Head Incorporated with Turbine Flow Meter

QC2 dispense head with integrated volumetric flow-measuring turbine that displays the flow rate in real time for precise dosing from the container.

Configure it now!

Two Main Options:

  • Totalizer-allows verification of flow during dispensing process
    • Ensures Flow Rate
    • Verifies volume transferred
  • Batch control - easy integration for small transfer volumes. Ability to transfer only specified amounts.
    • Dosing and Mixing without the need of expensive metering pumps
    • Can be easily be programmed to send signals to process controls

Technical Data:

QC2-Series max flow rate:
  • Max flow rate: 8.4 gal/min

Materials of construction for body:
  • PE-HD
  • Available on request: PVDF
Other wetted parts:
  • Inner Turbine Components: PVDF
  • Bearing Turbine Shaft: Sapphire/Ceramics (AI203)
  • Seals: FKM, EPDM
Key Code:

  • Standard QC2 options
Flow Transducer:
  • Housing: PP
  • Housing seal: NBR
Measurement Data:
  • Measuring range: 2 lpm - 120 lpm
  • Start up: ≤ 1.5 lpm
  • Pulse rate: 256 pulses / L
  • Accuracy: ± 1.0% full scale
  • Repeatability: ± 0.5% Full scale
Operating Temperature:
  • -20ºC to 60ºC (-4ºF to 140ºF)

Pressure Loss:
  • 0.1 Bar at 3600 l/h (1.45 PSI at 15.85 GPM)
Electrical Connections:
  • Totalizer: Plug, type A DIN EN 175301-803
  • Batch controller: 1x 5-pin M12 device plug (A coded)
  • Voltage: ≤ 36 V DC/ 30V AC
  • Supply voltage: 18 - 30 V DC
  • Current: ≤ 2 A DC
  • Rating: ≤ 60 W
  • Recommended connection cable: 8-10 mm diameter
Item Numbers:
Batch Controller
DH-DCF-PE-XXX-F1/2″-F3/8″ (with FKM seals)
DH-DCE-PE-XXX-F1/2″-F3/8″ (with EPDM seals)

Totalizer
DH-DTF-PE-XXX-F1/2″-F3/8″ (with FKM seals)
DH-DTE-PE-XXX-F1/2″-F3/8″ (with EPDM seals)
  • Measuring certificate with calibration data included. Calibration with water temperature of 20 degrees Celsius.
  • Particles contained in the medium that are greater than 100 µm may cause blockage.
Data Sheet Dispense Head Incorporated with Turbine Flow Meter

In this section we would like to show you videos about our products.

To make this possible, we ask you to agree to "targeting", which allows us to show you YouTube videos directly on our site.

check resistance

This might also interest you

Dispense Head with Integrated Bubble Sensor

Report empty status easily and fully automatically. Dispense heads with integrated bubble sensor enable automatic operation.

learn more →

Fill and Dispense Heads with Limit Switch

Dispense and Fill Heads with built-in limit switch to signal the correct coupling with the dip tube.

learn more →

Fill Head with Mixing Nozzle

Fill Heads with mixing nozzles allow an homogeneous mixing of chemicals without additional mechanical stirrers.

learn more →

Fill Heads with integrated N2-blanketing port

Fill Heads with additional second vent port allow nitrogen blanketing and filling of the container afterwards in a closed loop.

learn more →

Ball valves with limit switch

G-Series Dispense and Fill Heads with a ball valve can be optionally equipped with a multifunctional module, which allows signalling when the ball valve is in the correct position.

learn more →



Data Sheet Dispense Head Incorporated with Turbine Flow Meter